Here is how to move the VisibleThread virtual machine to Microsoft Hyper-V.
Estimated Time: 40M - 1Hour
Steps to Migrate Visible Thread(VT) to Microsoft Hyper-V
- Download and Install: Starwind V2V Converter
- Know the location of the Virtual Appliance's VMDK file. If you have just downloaded the VisibleThread zip file, extract it to find the VMDK file.
- Convert Virtual Appliance VMDK file to VHD
- In the Starwind V2V Converter - Click the Browse button and select your VT Vmware Disk(VMDK)
- If asked to choose a destination image format, select 'Microsoft Virtual PC growable image'
- Select the location to save your VHD file
- Estimated time for VT 6-8GB took 40-50M using a Dell T5400 Precision Workstation with Xeon Processor, 8GB RAM, and SAS storage drives.
- Using the Hyper-V manager (Start Menu-> Administrative Tools-> Hyper-V manager)
- Create a New Hyper-V Virtual Machine, select 'New->Virtual Machine' from the menu on the right side of the Hyper-V manager
- Call the Virtual Machine 'VisibleThread Server', click 'Next'
- Allocate 4096MB memory to the Virtual Machine, click 'Next'
- Select to create a 'New Virtual Network' for the Virtual Machine and click 'Next'
- Select option to use an Existing VHD and browse for the new VHD file
- Select 'Standard Network Adapter'
- Start the VM (Generates new MAC Address for VM), right click on the VM and select 'Start'
- Connect to your new VM (right click on the VM and select 'Connect', then Click File > Settings
- Notate the MAC address for the legacy network device for the next steps
- Login to the VM and perform these steps
- The default username is 'visiblethread' and the password is 'password'
- type 'sudo rm /etc/udev/rules.d/70-persistent-net.rules'
- type 'nano /etc/network/interfaces'
- Replace MAC address with the new Hyper-V Mac Address on the line, “HWADDR”
- type 'Ctrl-O' and return to write the changes to disk and 'Ctrl-X' to exit
- Type 'sudo reboot'
6GB VMDK converted in 42M and 5s. Results will vary on the hardware used for the conversion process.
By default, the VisibleThread server is configured to pick up an IP address automatically from your network. To see what the ip configuration for the server is type the following at the command prompt, you should see something similar to what is displayed below:
eth0 Link encap:Ethernet HWaddr 40:40:2d:ef:41:54
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::4240:2dff:feef:4154/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17632221 errors:0 dropped:0 overruns:0 frame:0
TX packets:14928547 errors:0 dropped:0 overruns:0 carrier:0
RX bytes:8069857778 (8.0 GB) TX bytes:17026117038 (17.0 GB)
It may be useful to assign a static IP to the VisibleThread server. This way users can use a consistent address to connect to the VisibleThread server. To do so follow these steps:
Open the /etc/network/interfaces file using the pico editor:
sudo pico /etc/network/interfaces
In this file you should see the following line:
iface eth0 inet dhcp
Replace the word ‘dhcp’ with the word ‘static’ and add the relevant information for your network settings (ipaddress, gateway etc..), for example:
iface eth0 inet static
Save and close the /etc/network/interfaces file. To save the file type Ctrl-O i.e. control key and the letter o (which will prompt to save the file), then hit enter. Then to exit to the console type ctrl-x.
Restart the networking service on the Virtual Appliance:
Steve Kline - MCITP, RHCSA